Roofing Contractor in Roosevelt, NJ

Roosevelt is unlike any other town we serve. Built in the 1930s as the New Deal Jersey Homesteads, its core is roughly 200 Bauhaus-inspired homes with distinctive flat roofs, oversized windows, and cinder-block walls, and the entire town is on the National Register. Those flat roofs use membrane systems, not shingles, and they age and fail differently, so getting them right takes the right system and crew.

CRS handles all of it, from a flat-roofed Jersey Homesteads home to a newer pitched house on the edge of town. Here is what matters for a roof in Roosevelt.

Your Roofing Contractor in Roosevelt, NJ

CRS provides roof replacement, roof repair, roof restoration, emergency roofing, and protection plans across Roosevelt and the rest of Monmouth County. Every residential project begins with a free written inspection and a workmanship guarantee in writing.

How Much Does a Roof Cost in Roosevelt? (2026)

Most flat or low-slope Roosevelt roofs run $5,000 to $12,000 for a full replacement in 2026 depending on the system and size, while newer pitched homes run on the usual shingle scale. The figures below are planning ranges, not a quote.

Want your Roosevelt number? A free CRS inspection gives you a written report with photos and a real range for your exact roof. Request your free inspection.

Roosevelt Roofing Context

Roosevelt’s identity is its architecture. The original Jersey Homesteads, built from 1936 to 1938 as a New Deal cooperative for Jewish garment workers from New York, were designed by architect Alfred Kastner with a young Louis Kahn: single and attached homes with flat roofs, oversized windows, and spare geometric forms in cinder block. Artist Ben Shahn painted a mural here in 1937 and stayed, and the town was renamed for President Roosevelt after his death in 1945. The whole town is a National Register historic district, the only New Jersey municipality listed in its entirety. Newer pitched homes have been added over the years, but the flat-roofed core defines the roofing work here.

Flat and low-slope roofs are a different craft than pitched asphalt. The systems that work in New Jersey are modified bitumen, which is torch-applied, flexes in the cold, and resists freeze-thaw, and TPO, whose heat-welded seams outperform cheaper cold-adhesive installs and reflect heat. The most common failure point is ponding water and open seams, so proper slope and welded seams are everything.

On the historic homes, the flat roof and its detail carry the cost, and we respect the historic-district character. New Jersey’s 8 to 12 freeze-thaw cycles a winter are hard on aging flat seams, and the 2025 to 2026 season was the snowiest North Jersey since 2013 to 2014, so many of this spring’s leaks trace back to winter ice. A fair estimate specifies the right membrane and seam method, proper flashing at walls and penetrations, and a clear scope, with historic review handled where it applies. You can verify any New Jersey roofer through the NJ Division of Consumer Affairs before you sign.

Do You Need a Repair or a Full Replacement in Roosevelt?

On the flat roofs most leaks start at the seams and the flashing at walls and parapets; on pitched roofs at chimneys and valleys. Either way a targeted repair often holds. We would rather earn your trust with an honest repair now and your replacement when you actually need it.

Roosevelt Roof Inspection Checklist

• Flat-roof membrane and seam check. On the Jersey Homesteads flat roofs we inspect modified bitumen or TPO seams, the most common failure point, and confirm the right system for the roof.
• Ponding water and slope. We check for ponding that signals inadequate slope and may call for tapered insulation on a replacement.
• Wall and parapet flashing. On flat roofs the flashing at walls, parapets, and penetrations is where leaks start, so we inspect each detail.
• Historic-district character. On the original homes we respect the historic flat-roofed form and handle any district review the job needs.
• Winter freeze-thaw seam stress. New Jersey freeze-thaw cycles work leaks into flat seams, so we check the seams and any pitched eave protection.

For code and permit questions, the NJ Division of Codes and Standards is the authority, current storm data comes from the National Weather Service, and shingle specifications are published by manufacturers such as GAF.